Skip to main content

Veeam NSClient++ NRPE

The Veeam Monitoring Connector works with the Centreon NSClient++ monitoring agent and Powershell to check the operating status of a Veeam server.

Pack assets​

Templates​

The Monitoring Connector Veeam brings a host template:

  • App-Veeam-NRPE-custom

The connector brings the following service templates (sorted by the host template they are attached to):

Service AliasService TemplateService Description
Job-StatusApp-Veeam-Job-Status-NRPE-customCheck job status

The services listed above are created automatically when the App-Veeam-NRPE-custom host template is used.

Collected metrics & status​

Here is the list of services for this connector, detailing all metrics linked to each service.

Metric nameUnit
jobs.detected.countcount
job#statusN/A
job#longN/A

Prerequisites​

Centreon NSClient++​

To monitor a Veeam backup solution through NRPE, install the Centreon packaged version of the NSClient++ agent. Please follow our official documentation and make sure that the NRPE server's configuration is correct.

Installing the monitoring connector​

Pack​

  1. If the platform uses an online license, you can skip the package installation instruction below as it is not required to have the connector displayed within the Configuration > Monitoring Connector Manager menu. If the platform uses an offline license, install the package on the central server with the command corresponding to the operating system's package manager:
dnf install centreon-pack-applications-veeam-nrpe
  1. Whatever the license type (online or offline), install the Veeam connector through the Configuration > Monitoring Connector Manager menu.

Plugin​

Use the commands below according to your operating system's package manager:

dnf install centreon-nrpe3-plugin

Using the monitoring connector​

Using a host template provided by the connector​

  1. Log into Centreon and add a new host through Configuration > Hosts.
  2. Fill in the Name, Alias & IP Address/DNS fields according to your resource's settings.
  3. Apply the App-Veeam-NRPE-custom template to the host. A list of macros appears. Macros allow you to define how the connector will connect to the resource, and to customize the connector's behavior.
  4. Fill in the macros you want. Some macros are mandatory.
MacroDescriptionDefault valueMandatory
NRPEPORTPort used to reach the NRPE server5666
NRPECLIENTNRPE Binary used to perform the checkcheck_centreon_nrpe
NRPETIMEOUTTimeout to connect to the NRPE Server55
NRPEEXTRAOPTIONSAny extra option you may want to add to every command (a --verbose flag for example). All options are listed here.
  1. Deploy the configuration. The host appears in the list of hosts, and on the Resources Status page. The command that is sent by the connector is displayed in the details panel of the host: it shows the values of the macros.

Using a service template provided by the connector​

  1. If you have used a host template and checked Create Services linked to the Template too, the services linked to the template have been created automatically, using the corresponding service templates. Otherwise, create manually the services you want and apply a service template to them.
  2. Fill in the macros you want (e.g. to change the thresholds for the alerts). Some macros are mandatory (see the table below).
MacroDescriptionDefault valueMandatory
FILTERENDTIMEFilter job with end time greater than current time less value in seconds (default: 86400)86400
FILTERNAMEFilter job name (can be a regexp)
FILTERSTARTTIMEFilter job with start time greater than current time less value in seconds
FILTERCOUNTERSOnly display some counters (regexp can be used).
OKSTATUSDefine the conditions to match for the status to be OK. You can use the following variables: %{display}, %{status}, %{type}, %{is_running}, %{scheduled}
WARNINGLONGSet warning threshold for long jobs. You can use the following variables: %{display}, %{status}, %{type}, %{elapsed}
CRITICALLONGSet critical threshold for long jobs. You can use the following variables: %{display}, %{status}, %{type}, %{elapsed}
CRITICALSTATUSDefine the conditions to match for the status to be CRITICAL (default: '%{is_running} == 0 and not %{status} =~ /Success/i'). You can use the following variables: %{display}, %{status}, %{type}, %{is_running}, %{scheduled}%{is_running} == 0 and not %{status} =~ /Success/i
WARNINGSTATUSDefine the conditions to match for the status to be WARNING. You can use the following variables: %{display}, %{status}, %{type}, %{is_running}, %{scheduled}
EXTRAOPTIONSAny extra option you may want to add to the command (a --verbose flag for example). All options are listed here.--verbose
  1. Deploy the configuration. The service appears in the list of services, and on the Resources Status page. The command that is sent by the connector is displayed in the details panel of the service: it shows the values of the macros.

How to check in the CLI that the configuration is OK and what are the main options for?​

Once the plugin is installed, log into your Centreon poller's CLI using the centreon-engine user account (su - centreon-engine). Test that the connector is able to monitor a resource using a command like this one (replace the sample values by yours):

/usr/lib64/nagios/plugins//check_centreon_nrpe -H 10.0.0.1 -p 5666 -t 55  -c check_centreon_plugins -a 'apps::backup::veeam::local::plugin' 'tape-jobs'  ' \
    --filter-name="" \
    --warning-status="" \
    --critical-status="%{enabled} == 1 and not %{last_result} =~ /Success|None/i" \
    --warning-total="" \
    --critical-total="" \
    --verbose'

The expected command output is shown below:

OK: total jobs: 41 All jobs are ok | 'tapejobs.total.count'=41;;;0;

Troubleshooting​

Please find the troubleshooting documentation for Centreon Plugins typical issues.

Available modes​

In most cases, a mode corresponds to a service template. The mode appears in the execution command for the connector. In the Centreon interface, you don't need to specify a mode explicitly: its use is implied when you apply a service template. However, you will need to specify the correct mode for the template if you want to test the execution command for the connector in your terminal.

All available modes can be displayed by adding the --list-mode parameter to the command:

/usr/lib64/nagios/plugins//check_centreon_nrpe -H 10.0.0.1 -p 5666 -t 55  -c check_centreon_plugins -a 'apps::backup::veeam::local::plugin' 'tape-jobs'  ' \
    --filter-name="" \
    --list-mode'

The plugin brings the following modes:

ModeLinked service template
job-status [code]App-Veeam-Job-Status-NRPE-custom
licenses [code]App-Veeam-Licenses-NRPE-custom
list-jobs [code]Not used in this Monitoring Connector
list-repositories [code]Not used in this Monitoring Connector
repositories [code]App-Veeam-Repositories-NRPE-custom
tape-jobs [code]App-Veeam-Tape-Jobs-NRPE-custom
vsb-jobs [code]App-Veeam-Vsb-Jobs-NRPE-custom

Available options​

Generic options​

All generic options are listed here:

OptionDescription
--modeDefine the mode in which you want the plugin to be executed (see--list-mode).
--dyn-modeSpecify a mode with the module's path (advanced).
--list-modeList all available modes.
--mode-versionCheck minimal version of mode. If not, unknown error.
--versionReturn the version of the plugin.
--pass-managerDefine the password manager you want to use. Supported managers are: environment, file, keepass, hashicorpvault and teampass.
--verboseDisplay extended status information (long output).
--debugDisplay debug messages.
--filter-perfdataFilter perfdata that match the regexp. Example: adding --filter-perfdata='avg' will remove all metrics that do not contain 'avg' from performance data.
--filter-perfdata-advFilter perfdata based on a "if" condition using the following variables: label, value, unit, warning, critical, min, max. Variables must be written either %{variable} or %(variable). Example: adding --filter-perfdata-adv='not (%(value) == 0 and %(max) eq "")' will remove all metrics whose value equals 0 and that don't have a maximum value.
--explode-perfdata-maxCreate a new metric for each metric that comes with a maximum limit. The new metric will be named identically with a '_max' suffix). Example: it will split 'used_prct'=26.93%;0:80;0:90;0;100 into 'used_prct'=26.93%;0:80;0:90;0;100 'used_prct_max'=100%;;;;
--change-perfdata --extend-perfdataChange or extend perfdata. Syntax: --extend-perfdata=searchlabel,newlabel,target[,[newuom],[min],[m ax]] Common examples: Convert storage free perfdata into used: --change-perfdata='free,used,invert()' Convert storage free perfdata into used: --change-perfdata='used,free,invert()' Scale traffic values automatically: --change-perfdata='traffic,,scale(auto)' Scale traffic values in Mbps: --change-perfdata='traffic_in,,scale(Mbps),mbps' Change traffic values in percent: --change-perfdata='traffic_in,,percent()'
--extend-perfdata-groupAdd new aggregated metrics (min, max, average or sum) for groups of metrics defined by a regex match on the metrics' names. Syntax: --extend-perfdata-group=regex,namesofnewmetrics,calculation[,[ne wuom],[min],[max]] regex: regular expression namesofnewmetrics: how the new metrics' names are composed (can use $1, $2... for groups defined by () in regex). calculation: how the values of the new metrics should be calculated newuom (optional): unit of measure for the new metrics min (optional): lowest value the metrics can reach max (optional): highest value the metrics can reach Common examples: Sum wrong packets from all interfaces (with interface need --units-errors=absolute): --extend-perfdata-group=',packets_wrong,sum(packets_(discard |error)_(in|out))' Sum traffic by interface: --extend-perfdata-group='traffic_in_(.*),traffic_$1,sum(traf fic_(in|out)_$1)'
--change-short-output --change-long-outputModify the short/long output that is returned by the plugin. Syntax: --change-short-output=pattern~replacement~modifier Most commonly used modifiers are i (case insensitive) and g (replace all occurrences). Example: adding --change-short-output='OK~Up~gi' will replace all occurrences of 'OK', 'ok', 'Ok' or 'oK' with 'Up'
--change-exitReplace an exit code with one of your choice. Example: adding --change-exit=unknown=critical will result in a CRITICAL state instead of an UNKNOWN state.
--range-perfdataRewrite the ranges displayed in the perfdata. Accepted values: 0: nothing is changed. 1: if the lower value of the range is equal to 0, it is removed. 2: remove the thresholds from the perfdata.
--filter-uomMask the units when they don't match the given regular expression.
--opt-exitReplace the exit code in case of an execution error (i.e. wrong option provided, SSH connection refused, timeout, etc). Default: unknown.
--output-ignore-perfdataRemove all the metrics from the service. The service will still have a status and an output.
--output-ignore-labelRemove the status label ("OK:", "WARNING:", "UNKNOWN:", CRITICAL:") from the beginning of the output. Example: 'OK: Ram Total:...' will become 'Ram Total:...'
--output-xmlReturn the output in XML format (to send to an XML API).
--output-jsonReturn the output in JSON format (to send to a JSON API).
--output-openmetricsReturn the output in OpenMetrics format (to send to a tool expecting this format).
--output-fileWrite output in file (can be combined with json, xml and openmetrics options). E.g.: --output-file=/tmp/output.txt will write the output in /tmp/output.txt.
--disco-formatApplies only to modes beginning with 'list-'. Returns the list of available macros to configure a service discovery rule (formatted in XML).
--disco-showApplies only to modes beginning with 'list-'. Returns the list of discovered objects (formatted in XML) for service discovery.
--float-precisionDefine the float precision for thresholds (default: 8).
--source-encodingDefine the character encoding of the response sent by the monitored resource Default: 'UTF-8'.

Modes options​

All available options for each service template are listed below:

OptionDescription
--timeoutSet timeout time for command execution (default: 50 sec)
--no-psDon't encode powershell. To be used with --command and 'type'command.
--commandCommand to get information (default: 'powershell.exe'). Can be changed if you have output in a file. To be used with --no-ps option!!!
--command-pathCommand path (default: none).
--command-optionsCommand options (default: '-InputFormat none -NoLogo -EncodedCommand').
--ps-displayDisplay powershell script.
--ps-exec-onlyPrint powershell output.
--filter-nameFilter job name (can be a regexp).
--exclude-nameExclude job name (regexp can be used).
--filter-typeFilter job type (can be a regexp).
--filter-start-timeFilter job with start time greater than current time less value in seconds.
--filter-end-timeFilter job with end time greater than current time less value in seconds (default: 86400).
--ok-statusDefine the conditions to match for the status to be OK. You can use the following variables: %{display}, %{status}, %{type}, %{is_running}, %{scheduled}.
--warning-statusDefine the conditions to match for the status to be WARNING. You can use the following variables: %{display}, %{status}, %{type}, %{is_running}, %{scheduled}.
--critical-statusDefine the conditions to match for the status to be CRITICAL (default: '%{is_running} == 0 and not %{status} =~ /Success/i'). You can use the following variables: %{display}, %{status}, %{type}, %{is_running}, %{scheduled}.
--warning-longSet warning threshold for long jobs. You can use the following variables: %{display}, %{status}, %{type}, %{elapsed}.
--critical-longSet critical threshold for long jobs. You can use the following variables: %{display}, %{status}, %{type}, %{elapsed}.
--warning-totalSet warning threshold for total jobs.
--critical-totalSet critical threshold for total jobs.

All available options for a given mode can be displayed by adding the --help parameter to the command:

/usr/lib64/nagios/plugins//check_centreon_nrpe -H 10.0.0.1 -p 5666 -t 55  -c check_centreon_plugins -a 'apps::backup::veeam::local::plugin' 'tape-jobs'  ' \
    --filter-name="" \
    --warning-status="" \
    --help